SVX Network Forums Live Chat! SVX or Subaru Links Old Lockers Photo Post How-To Documents Message Archive SVX Shop Search |
IRC users: |
|
#1
|
|||
|
|||
Installing Polish bushings .. ?
Got the Rt front control arm out (doing wheel bearing also).. to start installing my Polish poly bushing set.. I've done a fair amount of press work, but I can't figure out how to get the control arm bushings out?? How to set up the press.. to take them out? Am I missing something obvious? I never had this problem before .. ??
HeLp!? Thanks, Jim
__________________
Jim 1995 Laguna Blue SVX AWD L - 240K (daily driver) - "ReBuILT" used engine at 236K miles (6/13) 2013 Veloster Red - Driver Now??Dropsprings [1/2" rear, 1" front] with Koni Strut Inserts> Magnaflow Exhaust System> ECUTune Stage 1av1 Upgrade (from 1v4)> ECUTune TCU MOD> Aluminum Crankshaft Pulley> Stainless Brake Lines> Phenolic Spacers> Perforated Brake Rotors (dint like, OEM now)> SmallCar Shift Kit (resting since TCU MOD)> 7-Position Ground System> High-Pressure Fuel Pressure Regulator (resting)> ATF Cooler & Campaign Filter> Yellow Polish Polyurethane Bushings> Pioneer Double-DIN Stereo with JL AUDIO Speakers> Driveshaft Rebuilt with C-Clip U-Joints> 15 Min MOD> 20 Min MOD .. . (2011) Valentine One Radar Detector with Remote Display - ucan'tseeme! |
#2
|
||||
|
||||
Re: Installing Polish bushings .. ?
There is another page somewhere on doing this - anyone else remember?
|
#3
|
|||
|
|||
Re: Installing Polish bushings .. ?
you can either do it with the press by positioning it over a piece of large diameter pipe with a notch cut into so the control arm can hang while the bushing is under the press or use sockets and some all thread. to do the socket method you need the pull socket to be large enough to grab the bushing but small enough to pass through the hole and the receiver socket to be just large enough that it won't pass through the hole. stick the all thread through both sockets and the bushing, thread nuts with washers behind them until the all thread pulls the smaller socket with the bushing through the hole on the control arm.
was going to do some pics and instructions on this but haven't had time to even check the site for a couple months. hope this helps.
__________________
Current Stable: 1992 SVX 1979 K5 Blazer Cheyenne 1956 Plymouth Belvedere - Daisy 1967 Chevy C20 1953 Chevy 210 1969 Plymouth Satellite 1949 Chevy Thriftmaster 1959 Chevy Apache 1951 Chevy Stepside 1969 Chevy Camper Special 1978 Ford F150 w/ stroked 460 1986 Volvo 740 turbo wagon 1999 GMC 2500 Creep Van 1994 Impreza Outback |
#4
|
||||
|
||||
Re: Installing Polish bushings .. ?
He and I discussed it over PMs, and he got it figured out. Maybe he took some pics to help the next guy.
The key to using a press is having one of the thingy on the left of this picture:
__________________
'94 Laguna Blue LSi ~159k.......JDM ultra short-geared 3.900 STi Version 7 6-speed w/ Cobb shortshifter, ECUtune 244,8.1mm/256,9.1mm i/e cams, group N motor mounts, '97 grille, JDM clear corners, Momo JDM Legacy GT steering wheel, apkarian's LED tails, silver STi BBS wheels, PWR radiator, redstuff pads f/r, drilled/slotted rotors, bontragerworks rsb #18, Koni/GC 450f/375r coilovers, Megan Racing adjustable lateral links, KMac c/c plates, Stebro exhaust, ECUtune 1v5, Optima battery in the trunk where it belongs. Turbo project '97 Ebony LSi ~137k #036.......Power mode mod, JDM clear corners, BBS wheels. AUX/pocket mod Now a mod "over there" ............Photo album |
#5
|
|||
|
|||
Re: Installing Polish bushings .. ?
I believe it is called a bearing separator, sold at Harbor freight.
Ray |
#6
|
||||
|
||||
Re: Installing Polish bushings .. ?
I was wondering what they were called for a while now, thanks.
__________________
'94 Laguna Blue LSi ~159k.......JDM ultra short-geared 3.900 STi Version 7 6-speed w/ Cobb shortshifter, ECUtune 244,8.1mm/256,9.1mm i/e cams, group N motor mounts, '97 grille, JDM clear corners, Momo JDM Legacy GT steering wheel, apkarian's LED tails, silver STi BBS wheels, PWR radiator, redstuff pads f/r, drilled/slotted rotors, bontragerworks rsb #18, Koni/GC 450f/375r coilovers, Megan Racing adjustable lateral links, KMac c/c plates, Stebro exhaust, ECUtune 1v5, Optima battery in the trunk where it belongs. Turbo project '97 Ebony LSi ~137k #036.......Power mode mod, JDM clear corners, BBS wheels. AUX/pocket mod Now a mod "over there" ............Photo album |
|
|