Forum: SVX Cars For Sale
10-04-2009, 08:25 PM
|
Replies: 0
Views: 944
|
Forum: SVX Cars Wanted
08-18-2009, 08:53 PM
|
Replies: 15
Views: 3,382
Re: SVX wanted
What is a reasonable price to sell 92 with bad transmission - rest of car average shape?
JD
|
Forum: Technical Q & A
11-19-2006, 11:48 PM
|
Replies: 1
Views: 798
Planetary gear failure
What are the main causes of planetary gear failure in a transmission that has larger trans fluid cooler. I have had two back to back failures. Different transmissions-same car.
JD
|
Forum: Technical Q & A
10-06-2006, 09:11 PM
|
Replies: 1
Views: 758
Also need tranny advice
Installed used 4.11 tranny from 2.5 Legacy-worked out bugs, ran well for 800 miles. Changed trans resistor from 130 ohms to 37 ohms and within 100 miles I
have the following issues:
In park you...
|
Forum: Technical Q & A
09-30-2006, 11:07 PM
|
Replies: 2
Views: 1,032
clutches can be replced with compressor...
clutches can be replced with compressor installed- I have done it. The bearing is
sometimes hard to find to purchase. I would assume the noise is the bearing. The bearing turns regardless if the AC...
|
Forum: Technical Q & A
09-24-2006, 11:42 PM
|
Replies: 4
Views: 1,299
drive vibration problem solved
I changed three things
put in fourth drive flange bolt that I forgot to install
put pb then oil in the slightly stiff u joint
matched paint marks on driveshaft and rear flange
vibration at 43...
|
Forum: Technical Q & A
09-18-2006, 11:13 PM
|
Replies: 4
Views: 1,299
They were stiff but moveable. What level of...
They were stiff but moveable. What level of movement typically causes vibration-for example the joint falls down under it's own weight etc?
Also, if drive shaft and flanges were marked for...
|
Forum: Technical Q & A
09-17-2006, 04:26 PM
|
Replies: 4
Views: 1,299
|
Forum: Technical Q & A
09-16-2006, 10:18 AM
|
Replies: 4
Views: 1,299
severe vibration-need help
I finally installed the 1996 legacy 4eat with converted #2 speed sensor, converted rear(put 96 rear gear on original limited slip gear set). the speedometer reads correctly and I do not have error...
|
Forum: General SVX Babble
08-22-2006, 11:19 PM
|
Replies: 240
Views: 40,065
speed sensor for 4.11 swap
I just finished 4.11 swap from 96 legacy- seems like the swaps listed would have the thre wire/two wire problem on speed sensor #2. How did you guys resolve the connection
92 Claret 4.11 with...
|
Forum: Technical Q & A
08-22-2006, 04:26 PM
|
Replies: 73
Views: 15,801
#2 speed sensor
It is located near the dipstick for the diff--up front. I am tempted to try to graft the three wire top onto the gear for the two wire--
|
Forum: Technical Q & A
08-21-2006, 11:05 PM
|
Replies: 73
Views: 15,801
speed sensor - us 96 legacy in SVX
I did not follow thread regarding two wire sensor. I installed a us 1996 legacy 4eat in my svx. The speed sensor #2 out of the svx trans would not fit in the legacy- different drive mechanism. The...
|
Forum: Technical Q & A
06-10-2006, 08:14 AM
|
Replies: 1
Views: 834
seal
seal is available- I bought and installed- I work in ac oem so we buy from rebuilder/distributor-problem is I am going to Mirabel and will be back in one week I can buy for you and ship probably $18...
|
Forum: Technical Q & A
05-29-2006, 10:56 PM
|
Replies: 40
Views: 5,987
2 wire vs 3 wire
I bought a 96 legacy 4eat to put in theee svx. The speed drives at the rh axle are different one is square one drive is a slot- so it does not appear I can put the 3 wire svx into the 96 legacy...
|
Forum: Technical Q & A
05-22-2006, 11:39 PM
|
Replies: 10
Views: 1,505
|
Forum: Technical Q & A
05-10-2006, 09:11 PM
|
Replies: 10
Views: 1,505
|
Forum: Technical Q & A
05-07-2006, 10:15 PM
|
Replies: 10
Views: 1,505
|
Forum: Technical Q & A
05-07-2006, 01:42 PM
|
Replies: 7
Views: 1,272
|
Forum: Technical Q & A
05-07-2006, 01:16 PM
|
Replies: 10
Views: 1,505
need help rebulding auto tranny
Against the advice of this forum, I went ahead and replaced the friction discs on the 4eat from a kit. $250 total plus my labor(hobby). It ran 4000 miles until, while driving to anniversary dinner...
|
Forum: Technical Q & A
03-28-2006, 09:01 PM
|
Replies: 13
Views: 1,218
|
Forum: Technical Q & A
03-26-2006, 11:38 PM
|
Replies: 13
Views: 1,218
tranny resistor
Several threads discuss the resistor disconnected, small car mod- however does anyone know how the transmission uses the resistance or lack of resistance in adjusting shifting. I seen 60 ohms,...
|
Forum: Technical Q & A
03-12-2006, 03:17 PM
|
Replies: 18
Views: 1,743
tps
I set my TPS to .5 with- engine not running. It was originally at .35v. The reason I reset TPS is that only with the shift position in "3" , going down a fairly steep hill, the engine would "engine...
|
Forum: Technical Q & A
03-06-2006, 11:38 PM
|
Replies: 9
Views: 1,084
The high pressure is leaking - the rack is wet...
The high pressure is leaking - the rack is wet clear to the drivers(left) side.
I am going to call a Boulder hose shop. The ad for them specifically mentions replacement steering hose. The dealer...
|
Forum: Technical Q & A
03-06-2006, 11:30 PM
|
Replies: 4
Views: 927
|
Forum: Chris's SVX Shop
03-05-2006, 11:36 PM
|
Replies: 10
Views: 915
repair done-works!
I "rebuilt" the svx transmission, replacing the friction and steels and the seals on the shafts. I now have 500 miles on the car-- WOW, transmission works great so far---:D :D I see why the members...
|