SVX Network Forums Live Chat! SVX or Subaru Links Old Lockers Photo Post How-To Documents Message Archive SVX Shop Search |
IRC users: |
#1
|
||||
|
||||
Rotors - vented Vs solid
OK my Baby has sold rears, can I fit vented (are they interchangable).
Are there any advantages - vented being on the rear? thanks Steve in NZ |
#2
|
||||
|
||||
Re: Rotors - vented Vs solid
Quote:
The rear doesn't have a heating warping problem as a rule. (My 2C worth) Keith |
#3
|
||||
|
||||
Re: Rotors - vented Vs solid
You have solid rears? Isn't yours a JDM car? JDM's came with slotted rears, as I recall, so someone may have changed your to solid rotors at a previous brake job. USDM SVXii came with solid rear rotors, so when I tried to buy rotors and got slotted ones, I found out they didn't fit.
I would bet that if you buy a set of slotted rotors they will fit your car perfectly.
__________________
Chris 92 Ebony Mica LS-L "A Rolling Restoration": 223,250 KM - Sleeping 2007 STi 6MT, Stance GR+ coilovers, PWR Rad, JDM hood badge, svxfiles 6000K HIDs, JDM Clear Corners, $15/15 min mod, $20/20 min mod, Energy Swaybar Bushings, Hella Supertones horns, Gold STi BBS rims, Group A lightweight crank pulley, A/C system removed, Custom header-back exhaust, Hybrid carbon/metal rear sway bar, restored headlights with CCFL halos 2008 Subaru Legacy Spec B - Diamond Grey Metallic - Sold 2020 Ram 1500 Longhorn - Red Pearl |
#4
|
||||
|
||||
Re: Rotors - vented Vs solid
Mine are solid - they have been from new - even though here in NZ & AUS we got the same running gear (gearbox / diffs / ratio splits etc) - I have checked with the Subaru guys here & found out that the local market in NZ spec'd solid rear rotors - hence the original question about whether vented would fit, I will ask Dayle at Motorsport warehouse if the USA vented / non-vented dimensions are.
thanks Steve in NZ |
#5
|
||||
|
||||
Re: Rotors - vented Vs solid
Ah, cool. Take a look at your capiler mounting bracket, that was what I found to be the problem with running slotted in my car. My bracket will only permit the thinner, solid rotors. The JDM vented rotors are 18mm thick. I couldn't find the specs on the solid ones, but probably 14mm or so.
__________________
Chris 92 Ebony Mica LS-L "A Rolling Restoration": 223,250 KM - Sleeping 2007 STi 6MT, Stance GR+ coilovers, PWR Rad, JDM hood badge, svxfiles 6000K HIDs, JDM Clear Corners, $15/15 min mod, $20/20 min mod, Energy Swaybar Bushings, Hella Supertones horns, Gold STi BBS rims, Group A lightweight crank pulley, A/C system removed, Custom header-back exhaust, Hybrid carbon/metal rear sway bar, restored headlights with CCFL halos 2008 Subaru Legacy Spec B - Diamond Grey Metallic - Sold 2020 Ram 1500 Longhorn - Red Pearl |
#6
|
||||
|
||||
Re: Rotors - vented Vs solid
Yes they are thinner than 18mm - I suspect that you are right about the thickness...
|
#7
|
||||
|
||||
Re: Rotors - vented Vs solid
I got new rotors from Applied Rotor Technologies (ART) Both rear & front were vented & slotted. No trouble with fit & have stood up well. I think they are the same as Nissan Pathfinder. They were no more than OEM rotors.
http://www.subaru-svx.net/photos/fil..._BABY/4371.jpg http://www.subaru-svx.net/photos/fil..._BABY/4367.jpg http://www.subaru-svx.net/photos/fil...BABY/4388.html |
#8
|
||||
|
||||
Re: Rotors - vented Vs solid
Quote:
I could be wrong but, unless you use a lot thiner pad, I doubt you could ever get a vented disk into the rear. |
#9
|
||||
|
||||
Re: Rotors - vented Vs solid
Yes that is what I have found out - measured a JDM version & compared it with the NZ spec'd one - no-go.
Thanks to everyone who sorted this one out for me .... |
#10
|
|||
|
|||
Re: Rotors - vented Vs solid
I have put both slotted/drilled on my 95 LSI both front and rear and have no problems. They are also vented as well. Put in ceramic kevlar pads front and rear with no problems. Also put in the PWR radiator and that fit perfectly. Body work being done as we speak.
Boi |
#11
|
||||
|
||||
Re: Rotors - vented Vs solid
I got drilled and slotted on the front and rear. They are great cause my rims are always clean since I get no brake dust build up! If you don't care about JDM vs USDM you can get them for a good price form NAPA you can also order form the motorsportwarehouse.com
__________________
Meow |
#12
|
||||
|
||||
Re: Rotors - vented Vs solid
You may have me there. It's been a while since they were installed. I'll check when I switch to my winter tires & report back.
|
#13
|
||||
|
||||
Re: Rotors - vented Vs solid
How many miles do you have on your ART rotors? I have 40,000+ on mine (front only). I just changed the pads, the rotors look super. I got 40,000+ miles out of Akebono ceramic pads.
__________________
LS-L 92 black top silver bullet-Turned into a 2005 Jeep TJ Unlimited 2012 Outback 3.6R Limited! |
#14
|
||||
|
||||
Re: Rotors - vented Vs solid
I just switched to solid because mine were starting to show cracks around the cuts and holes. Plus you can't cut slotted rotors. I've only driven the solid rotors for a short while but they seem very good.
|
#15
|
||||
|
||||
Re: Rotors - vented Vs solid
Quote:
Dave
__________________
LS-L 92 black top silver bullet-Turned into a 2005 Jeep TJ Unlimited 2012 Outback 3.6R Limited! |
|
|