info for engine rebuild.

[mikecg]

I planning on getting another engine for a project. I need some info from anyone who has a manual. I need all the engine specs for a rebuild. i.e. Torque specs, compression, timing ect. If you could scan the engine section of the manual and email it, or photocopy it and mail it I'd owe you. Anyone here that can help me out?

[immortal_suby]

Someone posted the cd service manual.

service manual cd

Not sure how much of a help it will be compared to the factory manuals though.

[Mr. Pockets]

Scanning the entire engine section and posting it would be a pretty big deal. I don't have a problem with scanning a page or two for somebody occasionally, but I would have a problem with scanning and posting an entire section. First, it'd be a lot of work. Second, it's a much larger copyright offense.

I recommend that you buy the factory service manuals.

[Subafreak]

For something cheaper and eaisier to find just go to Pepboys, Auto Palace or Zone or any of those type stores. They should have the Chiltons book that has all that info and alot more that you could care less about. Good buy thoe.

[mikecg]

I've been looking for a Chiltons. They told me it was no long in print for the SVX. I was hoping to avoid bbuying the dealer manual, but I may have too.

[GreenMarine]

Just for the hell of it if you want a JDM Engine I can point ya in the right direction if ya want... Don't know if there will be any real diffrence in the engines but hey if ya want one just let me know...


P.S.---> International shipping will apply

[mikecg]

Originally posted by GreenMarineSVX
Just for the hell of it if you want a JDM Engine I can point ya in the right direction if ya want... Don't know if there will be any real diffrence in the engines but hey if ya want one just let me know...


P.S.---> International shipping will apply

I already got my eye on a U.S. one for $580 including shipping.

[SVXMAN2001]

mikecg,

What part of nj are you in? I am near northern jersey. I have the complete set of manuals that you need. I want to rebuild my engine eventually as well so i figure we would both be helping eachother out. PM me, chris

[GreenMarine]

Originally posted by mikecg


I already got my eye on a U.S. one for $580 including shipping.

That's a good deal man... never mind about the JDM engine then.

[SVX-FF]

Try this link.
http://www.partsamerica.com/PartDeta...pe=626&PTSet=A

if it does not work then try:

www.advanceautoparts.com

and use a 92 SVX and click on repair manual. I just bought one a few months ago. It is a special order though.

i am going to be rebuilding my engine here in the next couple months. is there any way you might be able to write down, after you are done, all the specs that i will need? or just strange stuff that you found while doing it that might require a special way of doing it? I've researched a lot but mostly the electrical systems, i know those really well, if you need any help of that sort.

[mikecg]

Originally posted by SVXMAN2001
mikecg,

What part of nj are you in? I am near northern jersey. I have the complete set of manuals that you need. I want to rebuild my engine eventually as well so i figure we would both be helping eachother out. PM me, chris

I'm near Cape May. Saddly, North Jersey can be pretty far. I wouldnt mind helping you out if you want to dedicate a weekend and a place for me to crash. I'll make the drive so I can get a little exsperience. I have done rebuilds on older V-8 Chevys, but never anything this new, and never anything with fuel injection.

[SVXMAN2001]

mike, i pm'd you.

Chris

[wawazat??]

Originally posted by mtbikerco
i am going to be rebuilding my engine here in the next couple months. is there any way you might be able to write down, after you are done, all the specs that i will need? or just strange stuff that you found while doing it that might require a special way of doing it?

That's a pretty big request. I've torn my engine down to replace headgaskets and couldn't even think about a complete re-build without the service manuals (especially after reviewing the section on removing pistons and rods).

I strongly recommend the purchase of the service manuals if you intend on doing this job yourself.

Todd

does anyone know where to get the service manual for under $100? I made the mistake of buying that one on cd off e-bay and that thing is pretty much worthless. I have the chilton book but need something more in depth.