Need some Sub Information

[Wikedjuggalo]

O.k I am getting my Sub and Amp and wanting to compile a How-To on an install, but I am still wondering on where to run the power wire, if anyone has a picture of where they ran it I'd love to know ^^

[Tim]

I ran mine through the hole on the passenger side where the evaporator hose goes through.

The other area you can run it through is where the pedals are drilled through the firewall

[94SubieSVX]

There was a 1/2" hole kind-of down and to the left of the brake reservoir(looking from the engine bay into the car).

And the power wire ran along the firewall(now inside of the car) and down next to your left foot kick panel.

Then it was underneath the white plastic brake line protector piece. (I think its the brake lines??)


The power, and remote wire went through there for my setup.

[Wikedjuggalo]

Originally Posted by 94SubieSVX

There was a 1/2" hole kind-of down and to the left of the brake reservoir(looking from the engine bay into the car).

And the power wire ran along the firewall(now inside of the car) and down next to your left foot kick panel.

Then it was underneath the white plastic brake line protector piece. (I think its the brake lines??)


The power, and remote wire went through there for my setup.

I think this will be my best route going out there now to attempt this ^^

[94SubieSVX]

I forgot to add that once it's passed the white protective piece, it just went underneath the back seat and into the trunk.

I'm sure if you wanted it to be better looking you could run it up through the trunk liner and have it drop down through one of the speaker holes, or the Security Module hole.

[redlightningsvx]

i ran mine through the driver fender, into a grommet that has a yellow covered wire going into it, then it comes out behind the kick panel and run it underneath the carpet straight back.

[Wikedjuggalo]

Its now around 10:30 I finished I'm so freaking tired. I will do a write up tomorrow, funny thing is those the plastic pieces around the rear speakers split from the sub and stuff.... Guess thats good ^^

[94SubieSVX]

Originally Posted by Wikedjuggalo

Its now around 10:30 I finished I'm so freaking tired. I will do a write up tomorrow, funny thing is those the plastic pieces around the rear speakers split from the sub and stuff.... Guess thats good ^^

Pretty much any SVX you see will have split speaker grilles. It's just one of those things

[YourConfused]

here is where I found to be the most direct route for running a pair of 4ga wires to the rear of the svx.
1: running power out thru the fender
2: inner fender side pic (other side of batt)
3: going thru rubber boot into drivers kick panel
4: wires inside car by factory fuse box, go to fuse block w/ 2 4ga in and 4 8ga out w/ 4 60 amp fuses (running 2000W RMS between 2 amps)
5: going back to truck under rear seat pivot

[Wikedjuggalo]

Originally Posted by 94SubieSVX

Pretty much any SVX you see will have split speaker grilles. It's just one of those things

They weren't split before I put it in >.<

[94SubieSVX]

Originally Posted by Wikedjuggalo

They weren't split before I put it in >.<

Ooohh...well in that case you must have some decent bass goin on

[redlightningsvx]

Originally Posted by YourConfused

here is where I found to be the most direct route for running a pair of 4ga wires to the rear of the svx.
1: running power out thru the fender
2: inner fender side pic (other side of batt)
3: going thru rubber boot into drivers kick panel
4: wires inside car by factory fuse box, go to fuse block w/ 2 4ga in and 4 8ga out w/ 4 60 amp fuses (running 2000W RMS between 2 amps)
5: going back to truck under rear seat pivot

This is how i did mine and it came out very clean looking when i was done

[YourConfused]

more pics (I have about 90 from the install, just waiting to do the write-up)
1: RCA's at the head unit
2: fuse block installed next to the the factory fuse block
3: in the middle of it all
4: trunk done
5: door w/ 3M insulation

[Wikedjuggalo]

Originally Posted by YourConfused

more pics (I have about 90 from the install, just waiting to do the write-up)
1: RCA's at the head unit
2: fuse block installed next to the the factory fuse block
3: in the middle of it all
4: trunk done
5: door w/ 3M insulation

I beat you to it ^^
gotta find out how to submit it, I used the passenger side to do mine. Your is different you should write one up