what do i need to keep for the 4.44....?

[snofrek]

i think i have found a 4.44 tranny and rear diff. so what do i need to save off the car that the tranny and diff are comeing off of so that it will fit on my 92 SVX? and also is there anything special that i might need or have to do to make the tranny bolt on right to fit my car?!......

[nextse7en]

You need to keep your rear diff, you will need to swap out the 4.44's internals into your 3.54 housing while retaining the LSD bits of the 3.54.

[snofrek]

Originally Posted by nextse7en

You need to keep your rear diff, you will need to swap out the 4.44's internals into your 3.54 housing while retaining the LSD bits of the 3.54.

another guy says that i need the rear diff that is for the 4.44 cuz it has to keep the same gear ratio? and u dont switch trannies, u just switch out internals? i thought u switched the tranny and rear diff?

[nextse7en]

You DO get the 4.44 rear diff, and swap the internals into YOUR rear diff.

SVX axles wont mate with a normal 4.44 diff, and the 4.44 diff you are getting does not have LSD.


Swapping the 4.44s rear end into the 3.54 rear end housing and ring gear fixes this problem.


-Patrick

[snofrek]

Originally Posted by nextse7en

You DO get the 4.44 rear diff, and swap the internals into YOUR rear diff.

SVX axles wont mate with a normal 4.44 diff, and the 4.44 diff you are getting does not have LSD.


Swapping the 4.44s rear end into the 3.54 rear end housing and ring gear fixes this problem.


-Patrick

ok cool, that makes sence! im assuming its the same for the tranny too? o and im guessing that when i take out all the old parts, the 4.44 parts will all fit in the housings all without any troubles too?! i hope!?

[nextse7en]

Don't need to replace the front diff, the axles just plug in the 4.44.

-Patrick

[snofrek]

Originally Posted by nextse7en

Don't need to replace the front diff, the axles just plug in the 4.44.

-Patrick

ok so i take out my tranny and put in the 4.44 tranny, and then just replace everything in the rear diff with the 4.44 parts?! and when i do replace the rear diff parts with the 4.44 parts, they will go in without any problems?!

Tom

[nextse7en]

Check SVXfiles locker (OT) for details, also the how to section are already provided in great detail.

-Patrick

[snofrek]

Originally Posted by nextse7en

Check SVXfiles locker (OT) for details, also the how to section are already provided in great detail.

-Patrick

thanx pat! that helps alot!!!

Tom

[svxfiles]

Originally Posted by nextse7en

Check SVXfiles locker (OT) for details, also the how to section are already provided in great detail.

-Patrick

Thanks, Pat!
Just saw this now.
Been in the garage AND at deaths door.

BTW, the how too is in my signature.
If you have a question, call me.
304-738-0012










That Guy keeps coming back!!!!!

[TomsSVX]

Originally Posted by svxfiles

That Guy keeps coming back!!!!!

ROFLMAO.... ya know, I can think of a few people who woulda been done by now

Tom

[nextse7en]

Snofrek,

If you don't mind the 3 hour drive, you could bring the car over here to the rainy Willamette valley and hondasucks and I could slap that puppy in there for not too much moolah.


-Patrick

[snofrek]

Originally Posted by nextse7en

Snofrek,

If you don't mind the 3 hour drive, you could bring the car over here to the rainy Willamette valley and hondasucks and I could slap that puppy in there for not too much moolah.


-Patrick

it will take me 8 hours to get to Willamette Valley, assuming that you're talking about the Willamette Valley in Oregon? i live in Boise, ID. and ok i found a tranny and rear diff off a 96 subaru outback, the 2.5L, THAT IS THE 4.44 FOR SURE, CORRECT?!?!?! cuz i can get both for $250!!!

[TomsSVX]

give us the trans code off the bellhousing by the starter

Tom

[snofrek]

Originally Posted by TomsSVX

give us the trans code off the bellhousing by the starter

Tom

ok, ill get that as soon as i get back and look at it.

Tom