SVX Network Forums Live Chat! SVX or Subaru Links Old Lockers Photo Post How-To Documents Message Archive SVX Shop Search |
IRC users: |
#1
|
|||
|
|||
How tough is it to replace valve cover gaskets?
Both sides are leaking, dos'nt look like a lot of room to work. Any tricks besides having "small" hands?...LOL
Also I don't have rear wheel drive, fuse is in, where's a rear drive servo? have looked under the car on the tailstock but I'm not seeing it...HELP!!! Last edited by robinhoodof she; 03-01-2009 at 05:32 PM. Reason: spelling mistake |
#2
|
||||
|
||||
Re: How tough is it to replace valve cover gaskets?
Check the "How-To Documents", I believe there is a write up on replacing them.
-Bill
__________________
Retired NASA Rocket Scientist Most famous NASA "Child" - OSIRIS-REx delivered samples from asteroid BENNU to Earth in Sept. 2023 Center Network Member #989 '92 Fully caged, 5 speed, waiting for its fully built EG33 '92 "Test Mule", 4:44 Auto, JDM 4:44 Rear Diff with Mech LSD, Tuned headers, Full one-off suspension '92(?) Laguna, 6 spd and other stuff (still at OT's place) My Locker |
#3
|
||||
|
||||
Re: How tough is it to replace valve cover gaskets?
Quote:
If there is, its hidden.
__________________
92 LS-L, Ebony Pearl, 160k miles, sitting in the hospital waiting room hoping for a miracle 06 Hyundai Sonata GLS, 77K miles |
#4
|
||||
|
||||
Re: How tough is it to replace valve cover gaskets?
If you go to the main page scrool down to Faqs and how to's it's there.
__________________
Seth 94' Barcelona Red w/ Tricoat black 2-tone AWD Ls -Sold Mods:AWD conversion/4.44 swap by Budfreak, Custom red interior lights, Custom Satin black dash, Power mode switch, Cold air intake, Permecool tranny filter,Sony xplode 10" sub, Sony xplode 1000w amp, Blitz in-line driver, DDM Tuning 6000k HID's, New paint job/body work by me, 97' Grill, QC shift kit, 17'' MB Motoring rims, 15&20 min mod, front & rear urethane swaybar bushings, Custom fiberglass sub box, Custom red led a/c control unit, perrin lightweight crank pulley, Black wrinkle finish powdercoated intake manifold w/ clear hoses , 02' outback heated/power black leather seats Soon to come:Fiberglass hood, upholster ALL suede to black leather Past subies: 92' Pearl White/black top LS-L-SOLD 96' Legacy Outback-TOTALED 99' Legacy Outback Limited 30th anniversary edition-TOTALED 98' Forester L -Totaled Other toys: 99' Forester S -WRX brake upgrade, soon an 04 wrx motor swap 06' B9 Tribeca-Stock 1982' Yamaha xj650 Maxim Mods: work in progress |
#5
|
||||
|
||||
Re: How tough is it to replace valve cover gaskets?
Quote:
Look through this post, http://www.subaru-svx.net/forum/showthread.php?t=44396 begin from #15 and go forward from there.
__________________
The Worm _______________ June '91 Claret LSL #1733, Enkei RS-5's x 16", Original Paint, accompanied by Beautifully speckeled Front Bumper, Sony Audio Components, Small Car Shift Kit, "How to" Hood Lifts {Perfect}, "15 Minute Suspension Mod" Motorsport Floor Mats. Perma-Cool External T. Filter, New Front Axels {1/2008}. "Classic Radiators" unit "$36 coil alternative" and Tranny rebuild at 287k 8/2012 '05 Infinity G35 Coupe. No Mods, 33K Miles |
#6
|
||||
|
||||
Re: How tough is it to replace valve cover gaskets?
Gotcha. Just didn't see a link to it in the How-To documents.
__________________
92 LS-L, Ebony Pearl, 160k miles, sitting in the hospital waiting room hoping for a miracle 06 Hyundai Sonata GLS, 77K miles |
#7
|
||||
|
||||
Re: How tough is it to replace valve cover gaskets?
Get a spanner with the ratchett bit in the end. Tell you what that saved alot of time and fitted in the tight gap easly
__________________
1992 NZDM SVX Maroonish Red/Black ( 1st car ive owned with an cd player ) Has been retired 1989 Vortex 6 Maroon 1983 RX Silver Grey 1973 1400 GSR Yelo 2 Door Coupe awaiting Restoration |
|
|