SVX Network Forums Live Chat! SVX or Subaru Links Old Lockers Photo Post How-To Documents Message Archive SVX Shop Search |
IRC users: |
#16
|
||||
|
||||
ive tired to find little bubles while idling and they don't show.
It only overheated on me once(kinda). I got on it a little while taking a turn and accelled out of it. The heat went ice cold and the temp began to rise. I let the engine slow the car(5mt) And the heat came back on and the temp went back down. This was after quite a while of driving so I know the thermostat was open. Anyway, I am still pushing a good deal of coolant out throught the overflow and I replaced the cap. There is still coolant comming from the top of the cap. Anyway, its blowing my mind as to what it is. |
#17
|
||||
|
||||
The loss of heater heat would have been a result of an air pocket passing through the heater.
How soon does the water begins to spew? Before the engine warms up, or does it need to run several minutes first? If it is while the water is still relatively cold you probably have a compression leak. If only after the water is hot you may have a water pump not pumping (pulley or impeller slipping), or a severe blockage - mice or mouse house in the old radiator? Collapsed inner hose layer? Check the temp of the upper and lower hoses when it begins to spew to see if there is a large temp difference.
__________________
ASE Certified Master Automotive Technician w/L1. ASE Certified Master Medium/Heavy Truck Technician. Certified EVT (Emergency Vehicle Technician) |
#18
|
||||
|
||||
it won't leak unless the engine is reved. I don't mean little pansy revs either, it needs to be reved hard and there needs to be load on the enigne in order for the cap to leak.
|
#19
|
||||
|
||||
Well, that's when you need to have the cap off and be looking for bubbles. The question remains: will it do this when cold or does it need to be warmed up?
Needing to rev it up that hard is almost a dead giveaway...
__________________
ASE Certified Master Automotive Technician w/L1. ASE Certified Master Medium/Heavy Truck Technician. Certified EVT (Emergency Vehicle Technician) |
#20
|
||||
|
||||
dead give away to what? a compression leak?
|
#21
|
||||
|
||||
Well since you've changed the head gaskets and assumingly torqued everything properly perhaps the issue is with the head itself.
Either the head is warped from all the overheating or else it's cracked.
__________________
David B. SVXipedia @ SVX-IW.COM -- SVX Information Warehouse 2.0 coming...eventually! Ebony 1992 SVX LS-L 5 spd Koni/GC Stebro 187k miles RIP (Rust In Pieces) 1993 SVX 5 spd Koni/GC Stebro Polyurethane bushings still available! |
#22
|
||||
|
||||
i was afraid of that but i am quadruple checking everything over and over just to be absolutely positive
|
#23
|
||||
|
||||
Quote:
__________________
Danny 1994 Silver SVX in hybernation, awaiting for the monsterous awakening (Lebanon) 1967 Mercedes-Benz 250SL Euro Specs, Hard/Softtop, White/Red. Under Complete Restoration 2013 Mercedes-Benz SL350 Euro Specs, White/Red. Mint... Another step into SL Collection. |
#24
|
||||
|
||||
A couple of things can cause a leak in a fresh head gasket.
- Not running a tap down the head bolt holes / a die over the head bolts. - Reusing the old head bolts. **These can cause faulty torque readings and an insufficient seal - Not having the head resurfaced. - Not having the block checked for squareness/cut. **Uneven surfaces won't seal properly - Foreign material on the mating surface **Gots to be careful and keep everything clean If the leak is around the cylinder, which it probably is, only combustion gas (air/fuel mixture) will be entering the water. Won't see any oil in the water. There will be fuel but it will be harder to detect. Some mistakes are more expensive than others. Best to get it fixed before it ends up costing more. |
#25
|
||||
|
||||
Quote:
Tom, I spoke to my mechanic just now about your case, he told me that it is either the Head gaskets, or radiator, or the engine has uneven surface (totally flat as it should be) either to the side of the block, or the head (gasket surface)... either way if it is the case, you will have to shave it which will increase the compression ratio... FUTURE Turbo Mod???
__________________
Danny 1994 Silver SVX in hybernation, awaiting for the monsterous awakening (Lebanon) 1967 Mercedes-Benz 250SL Euro Specs, Hard/Softtop, White/Red. Under Complete Restoration 2013 Mercedes-Benz SL350 Euro Specs, White/Red. Mint... Another step into SL Collection. |
#26
|
||||
|
||||
no i am not looking to turbo this engine in the future. yes i will be removing the engine again and totally redoing the headgaskets. This time the heads will be pressure checked and milled. I need to call my head shop back and ask if they will aslo check the block, if not i will use a straight edge to the best I can. Ill let you know how it turns out.
|
#27
|
|||
|
|||
Danny,
As I recall an increase in compression ratio, caused by shaving the heads would be exactly the opposite of what one would do in preparation for "FUTURE Turbo Mod?"??? Glenn Sorry Tom!
__________________
"The only thing necessary for the triumph of evil is for good men to do nothing" Aaron Burke 1993 25th Anniversary Edition #63 of 301. R.I.P. Rojo 7/24/2008 She saved my life! 1997 Ebony Mica Pearl LSI. BLACKBERRY 1998 5-Spd Legacy GT Wagon in Glacier White: NUBURU 2005 Cadillac STS in Sandstorm Metallic: STORMY Veteran and farthest traveler of 1st SoCal2MuseumsMeet2010. http://www.subaru-svx.net/photos/user.php?RojoRocket Last edited by RojoRocket; 12-31-2004 at 07:43 PM. |
#28
|
||||
|
||||
Rojo you are right but lets not go over that here
Anyway, i bent the tabs on the cap to create a tighter seal. This seems to be working for now. Fingers toes arms and legs crossed that i don't need to pull the motor. But i am still expecting to have to do that. Just monitoring coolant levels and such as it is right now just to be absolutely sure there is a headgasket problem. |
|
|