06-07 WRX 4 pot brakes... FIT!

[STeeL25T]

Excellent work so far on this, I hope a rotor can be sourced. How much did those brakes cost you?

[BoxerFanatic]

Originally Posted by SilverSpear

Victor can you post the ones of the Subaru BAJA?

Doesn't baja have 5x100 bolt pattern?

The Maxima ones look decent, but the rotor hat height doesn't look the same, which will likely make it not fit.

320mm diameter and 24-25mm thickness, with the same hat dimensions (height, bolt pattern) as SVX would be something to look for.

The increase in diameter, and decrease in thickness would probably more than offset each other, in terms of thermal mass of the disc itself.

[the_paynter]

Yes the Baja is 5x100, it is based off the Legacy/outback.

Im going to give the maxima disc a try... if it doesnt fit, i will just return it. The difference in the hat makes it look like its not going to work though... dang

[SilverSpear]

Originally Posted by BoxerFanatic

Doesn't baja have 5x100 bolt pattern?

The Maxima ones look decent, but the rotor hat height doesn't look the same, which will likely make it not fit.

320mm diameter and 24-25mm thickness, with the same hat dimensions (height, bolt pattern) as SVX would be something to look for.

The increase in diameter, and decrease in thickness would probably more than offset each other, in terms of thermal mass of the disc itself.

The disc heights are approx the same as the SVX. The only difference are in the bolt patterns and the thickness...

Wonder how do aftermarket BBK for Bajas look like?

[alltrac]

Baja turbo

Baja non turbo

[1986nate]

they're 5x100- wont work

[SilverSpear]

But when you order aftermarket BBK for BAJA, the thickness comes minimum at 30mm and the hub is interchangeable, so you get the 5x114.3 instead...

I think Wilwood BBK is a nice affordable choice...

[Boxersix]

Just match up a Willwood or Coleman rotor ring to a billet hat from wilwood and you'll have your rotors.

I can do that for you easy as I have teh 2009 wilwood catalog sitting here in front of me. All I need from you is the rotor offset that's required, the rest of the specs were listed in the previous posts above. Measure the offset from the INSIDE surface of the rotor where it meets the hub to the rear face of the rotors.

Also, what's the hubcentric diameter on these cars?

[SilverSpear]

Originally Posted by Boxersix

Also, what's the hubcentric diameter on these cars?

58mm

[alltrac]

Originally Posted by 1986nate

they're 5x100- wont work

I was just ask to post the specs I could care less if they are 5x100

[the_paynter]

Originally Posted by Boxersix

Just match up a Willwood or Coleman rotor ring to a billet hat from wilwood and you'll have your rotors.

I can do that for you easy as I have teh 2009 wilwood catalog sitting here in front of me. All I need from you is the rotor offset that's required, the rest of the specs were listed in the previous posts above. Measure the offset from the INSIDE surface of the rotor where it meets the hub to the rear face of the rotors.

Also, what's the hubcentric diameter on these cars?

If someone got him this information that would be awesome, I cant get at that until the weekend as im no wheres near a jack/tools while during the week but i can make a run to toronto on the weekend and do it

[siceclipse]

DSM wheels are 5x114.3

i dont know the size of the disks so if you can find that out...

good luck

[the_paynter]

I know the Evo IX is to big... ill check out a 99 GSX though

EDIT:

I checked it out... says an eclipse front rotor is 10.83", way to small..POWER SLOT makes a big brake rotor replacement for it thought that is 12.5", this is 317.5mm which is good.. as for width and hat size.. not sure yet

Originally Posted by siceclipse

DSM wheels are 5x114.3

i dont know the size of the disks so if you can find that out...

good luck

[the_paynter]

2009 Acura TL uses a 5x114.3 bolt pattern in their 3.5L model.

The rotor size is 12.6"x1.1" ooooorrrrrr 320mm x 28mm.......

This might work... but 2 CM increase might be large. Doing the math though thats only 1cm added all the way around

Hat height anyone?

[sicksubie]

Can someone please go through the DBA catalogue already? Did you find anything BoxerSix?