SVX Network Forums Live Chat! SVX or Subaru Links Old Lockers Photo Post How-To Documents Message Archive SVX Shop Search |
IRC users: |
#1
|
|||
|
|||
front sway bar bushings
Hey all,
One of my sway bar bushings is destroyed. The dealer doesn't have the part in stock so I would like to go aftermarket with urethane replacements and get the parts today if I can (auto zone?) Does anybody know if there are aftermarket front urethane sway bushings available that would be direct swap with stock? I have search the forum and only found mention of the rear ones. Thanks, Matt. |
#2
|
|||
|
|||
if there are, nobody has found them yet. A mod was done with a spacer plate, but that requires some machine access - search if that interests you.
|
#3
|
||||
|
||||
I just got prothane bushings from motorsport warehouse and installed them this morning. I didn't use a spacer plate but instead just bolted them up with the included brackets so it raises the swaybar up a little bit. They are a little wider than stock and obviously much stiffer.
I just got back from the initial drive on some twisty backroads and the difference is incredible. I don't understand how but these 2 stupid little $20 bushings greatly reduced the body roll. Both of my stock bushings were shot - one was almost completely gone. It feels like I have new springs. In normal high speed cornering the car remains amazingly flat. Near the limit there is still some roll but much less than I had before. It's a huge improvement over what I had and compared to my wifes svx with stock bushings in good shape it is definitely better.
__________________
Matt Locker Link 2015 BRZ Limited 6MT 92 Ebony LS-L ECUtune Stage2av1, Z32 MAF, 370cc injectors, TomsSVX intake, BontragerWorks 22mm RSB #003, HID Hi and Lo beams, OT endlink and bushing mods, PWR Aluminum radiator, Harvey's QC shift kit, 2.5" flowmaster 80 exhaust, 17" Michelin Pilot Sport A/S, Poly sway bar bushings, Slotted Bradi rotors, AFBeefcake powdercoated calipers, 97 grill, and a huge set of air horns. 300,000 miles and counting 92 Ebony LS-L. ecutune stage1v4, motorsport 1pc pulley. Garage Queen - sold to Dad in upstate NY 155,000 miles 19 Subaru Ascent Premium - -Hers !. 89 DL 4x4 little red wagon - a.k.a. The immortal suby. 275k R.I.P. |
#4
|
||||
|
||||
I put energy suspention Sway bar bushing in my car, but I had to cut them down.
http://www.subaru-svx.net/photos/fil...cake/12689.JPG
__________________
2005 Legacy GT 2002 WRX VF22, Pinks, big TMIC and turbo back 128,*** miles My WRX's Cardomain Page |
#5
|
|||
|
|||
immortal_suby, how much did it raise the sway bar when you put them in? Not being a SVX suspension guru, I wonder if it the increase of the sway bar will affect the ride or wear to other suspension components or affects the understeer. ?? I was looking for a substitute bushings for replacement myself. How long did it take you complete the job? Maybe an email to Dayle is in order.
Wondering if Mychailo got a sway kit together??... Last edited by JLittell; 11-22-2003 at 01:08 PM. |
#6
|
||||
|
||||
Quote:
__________________
Mychailo :: 2006 Silver Mitsubishi Evolution 9, E85, 34 psi peak, 425wtq/505whp DJ :: 1995 Laguna Blue SVX L AWD 5MT (sold) Visit my locker SVX Mods: ND iridium spark plugs, Impreza RS fpr, afr tuned to 13.2:1 using a custom MAF bypass, custom exhaust, WRX 5MT w/ STi RA 1st-4th gear & stock WRX 5th gear, Exedy 13 lb flywheel & Sport Clutch, STi Group N tranny & engine mounts, urethane spacers in rear subframe, rear diff mounts, and pitch stopper, SVX Sport Strut Springs (185f/150r), custom 19 mm rear swaybar, urethane swaybar mounts, Rota Torque 17x8", 225/45-17 Proxes 4 tires, Axxis Deluxe Plus organic brake pads. |
#7
|
||||
|
||||
It raised it about 1/2 - 3/4 inch. So far after another drive I'd say any effect on handling is positive. There is some type of ball joint at either end of the sway bar where it attaches so I don't think it will introduce any significant binding that could increase wear but I'm no suspension expert so it's possible.
It took me about 2 hours to do it going slowly. This included time to look for new nuts/ bolts since the stock mounting is threaded and I had to find something to fit the new one which wasn't. Could be knocked down to about a half hour or less if I did them again. I haven't pushed it hard enough to break the tires loose so I'm not yet sure if it will understeer now. My svx normally oversteers so we'll see.
__________________
Matt Locker Link 2015 BRZ Limited 6MT 92 Ebony LS-L ECUtune Stage2av1, Z32 MAF, 370cc injectors, TomsSVX intake, BontragerWorks 22mm RSB #003, HID Hi and Lo beams, OT endlink and bushing mods, PWR Aluminum radiator, Harvey's QC shift kit, 2.5" flowmaster 80 exhaust, 17" Michelin Pilot Sport A/S, Poly sway bar bushings, Slotted Bradi rotors, AFBeefcake powdercoated calipers, 97 grill, and a huge set of air horns. 300,000 miles and counting 92 Ebony LS-L. ecutune stage1v4, motorsport 1pc pulley. Garage Queen - sold to Dad in upstate NY 155,000 miles 19 Subaru Ascent Premium - -Hers !. 89 DL 4x4 little red wagon - a.k.a. The immortal suby. 275k R.I.P. |
#8
|
||||
|
||||
Quote:
And anyone ever replace the steering rack bushings?
__________________
'92 Touring Ebony |
#9
|
|||
|
|||
'ey Immortal: Want to give us an update? I'm looking for bushings, and I'm not sure i I need the spacer plates or if I can just do what you did.
- Rob |
#10
|
||||
|
||||
Update - working well on my car. Bought a a second set for her svx and installed them not too long ago. Worked great on hers too using the same - bend the crap outta the bracket- method.
Car still oversteers and my azenis are pretty much slicks on the front and about 500 miles before they are slicks on the rear. Her car oversteers too but it was pretty much neutral before and she just has worn out avid v4's so not real sticky to begin with.
__________________
Matt Locker Link 2015 BRZ Limited 6MT 92 Ebony LS-L ECUtune Stage2av1, Z32 MAF, 370cc injectors, TomsSVX intake, BontragerWorks 22mm RSB #003, HID Hi and Lo beams, OT endlink and bushing mods, PWR Aluminum radiator, Harvey's QC shift kit, 2.5" flowmaster 80 exhaust, 17" Michelin Pilot Sport A/S, Poly sway bar bushings, Slotted Bradi rotors, AFBeefcake powdercoated calipers, 97 grill, and a huge set of air horns. 300,000 miles and counting 92 Ebony LS-L. ecutune stage1v4, motorsport 1pc pulley. Garage Queen - sold to Dad in upstate NY 155,000 miles 19 Subaru Ascent Premium - -Hers !. 89 DL 4x4 little red wagon - a.k.a. The immortal suby. 275k R.I.P. |
#11
|
|||
|
|||
Do you happen to have a part number on the sway bar set you recieved? I'd like to pick some up.
- Rob |
#12
|
|||
|
|||
Same here. Mine are about gone from oil exposure, soon to be remedied I hope! I looked on Dayle's site and don't find any swaybar bushings listed. Suppose we could just ask him?
Glenn
__________________
"The only thing necessary for the triumph of evil is for good men to do nothing" Aaron Burke 1993 25th Anniversary Edition #63 of 301. R.I.P. Rojo 7/24/2008 She saved my life! 1997 Ebony Mica Pearl LSI. BLACKBERRY 1998 5-Spd Legacy GT Wagon in Glacier White: NUBURU 2005 Cadillac STS in Sandstorm Metallic: STORMY Veteran and farthest traveler of 1st SoCal2MuseumsMeet2010. http://www.subaru-svx.net/photos/user.php?RojoRocket |
#13
|
||||
|
||||
Sorry man, threw out the package when I installed them, and Dayles gotta eat too.
__________________
Matt Locker Link 2015 BRZ Limited 6MT 92 Ebony LS-L ECUtune Stage2av1, Z32 MAF, 370cc injectors, TomsSVX intake, BontragerWorks 22mm RSB #003, HID Hi and Lo beams, OT endlink and bushing mods, PWR Aluminum radiator, Harvey's QC shift kit, 2.5" flowmaster 80 exhaust, 17" Michelin Pilot Sport A/S, Poly sway bar bushings, Slotted Bradi rotors, AFBeefcake powdercoated calipers, 97 grill, and a huge set of air horns. 300,000 miles and counting 92 Ebony LS-L. ecutune stage1v4, motorsport 1pc pulley. Garage Queen - sold to Dad in upstate NY 155,000 miles 19 Subaru Ascent Premium - -Hers !. 89 DL 4x4 little red wagon - a.k.a. The immortal suby. 275k R.I.P. |
#14
|
||||
|
||||
Quote:
|
#15
|
|||
|
|||
Quote:
- Rob |
|
|