SVX Network Forums Live Chat! SVX or Subaru Links Old Lockers Photo Post How-To Documents Message Archive SVX Shop Search |
IRC users: |
#1
|
||||
|
||||
how to adjust the clutch?
is there any way to adjust the clutch pedal to be more sensative? i pretty much have to floor it all the way to get it disengaged.
__________________
Tranny goes in, tranny comes out, tranny goes in.....AW ****, tranny comes out.... |
#2
|
||||
|
||||
Re: how to adjust the clutch?
Quote:
Hydro clutches should have something on the back of the pedal for adjustment before it hits the slave cyl. if I remember correctly... I know on mine (97 impreza) I've got the last year with the cable clutch, and the cable itself has a long screw/double locking nut combo on the end of it where it mounts to the bell housing before it hits the clutch fork. Definitely need more information to be helpful on this - and to be honest NASTICOC will be a better reference for anything regarding the clutch - only a very small number of members have their cars 5spd converted.
__________________
-Craig 94 LSi 5spd Barcelona Red, 14Xk miles. Full custom exhaust (Stebro cat-back, custom rest of the way forward) 8000K HID kit from Tom (SVXfiles), Energy Suspension front sway bar bushings, Non-Droopy visors, Race Concepts C/D + Dimpled Rotors, Axxis Ultimate pads,SS brake lines, Bontrager Works #009 (or something like that), stripped interior. (up next) Full cage, fuel cell, 327 swap |
#3
|
||||
|
||||
Re: how to adjust the clutch?
hydro clutch from an 04 wrx
__________________
Tranny goes in, tranny comes out, tranny goes in.....AW ****, tranny comes out.... |
#4
|
||||
|
||||
I actually have the same issue. I never really looked into adjusting it since I got pretty used to just pushing the pedal through the firewall* to get into first and reverse.
*exaggeration 02 WRX 5mt
__________________
"That which can be asserted without evidence can be dismissed without evidence." '92 Dark Teal SVX LS-L, >146,000m 3 pedals, 5 speeds., restoration underway. 2012 Honda Insight, slow but cute. |
#5
|
||||
|
||||
Re: how to adjust the clutch?
hows the 2nd gear holding up in that 02 wrx tranny? i hear its pretty weak
__________________
Tranny goes in, tranny comes out, tranny goes in.....AW ****, tranny comes out.... |
#6
|
||||
|
||||
It's hard to say. The whole trans was pretty much ass when I got it and I seemed to have figured out the method to driving it without grinding anything, but there are occasions when it will just not go into first or will get stuck in 2nd and I have no idea why.
2nd takes a little bit more force than the others to get in so there is definitely something worn-out in there. Sometimes I can slide it in but if I do that in traffic I'll be pissing someone off going so slow. 4th has a grind that only goes away with cold fluid and a delicate double-clutch shift below 4k. To be sincere I think that when I get it rebuilt there should be no reason for it to have any real problems. Seems like a pretty decent hunk of junk considering I've been rampaging the **** out of it.
__________________
"That which can be asserted without evidence can be dismissed without evidence." '92 Dark Teal SVX LS-L, >146,000m 3 pedals, 5 speeds., restoration underway. 2012 Honda Insight, slow but cute. |
#7
|
||||
|
||||
Re: how to adjust the clutch?
You did bleed it right? if so there is an adjustment on the back of the pedal from what I understand.
__________________
1994 SVX L - FWD Barcelona Red 190K miles ~ SOLD 1994 SVX LS - 5spd AWD Emerald Green 202k miles PWR Radiator, HID 5000k, New paint job with issues, 17" STI BBS wheels, converted to 5spd AWD from FWD. Purchased from SVXyGirl 2/20/09 -- Undergoing complete rebuild 1993 Justy 4wd 5door- Teal of sorts , beater. 2008 OBXT Newport Pearl 65k miles |
#8
|
||||
|
||||
Re: how to adjust the clutch?
I am all ****ing over this! (as long as its sort of like the hydrolic system in my DSM and Evo)
There should be an adjustment rod on the back of the clutch pedal that leads into the firewall. This rod is directly connected to the Master Cylinder. There should be a locking nut on the rod that holds it in place. Loosen the locking nut will allow you to turn the rod. Looking at the firewall as if you were sitting in the drivers seat, turning the rod "IN" (clockwise) will bring the engagement point more to the top, and turning the rod "OUT" (counterclockwise) will bring the engagement point closer to the bottom (foot on the floor). Make sure you tighten the lock nut when you are done. if you want/need visual aid, search "jacks transmissions" on youtube, or go to vfaq.com and look under "drivetrain" and click on "adjustment".
__________________
Mike 1992 SVX LS-L Pearl White 102,000 miles (Gone) 2005 Evolution 8 SSL Tarmac Black (new daily) 1995 Eclipse GSX Durango Copper Pearl (teh beast) 276awhp/280awtq @ 18psi (560's inj) 260awhp/260awtq @ 17psi (stock inj) |
#9
|
||||
|
||||
Re: how to adjust the clutch?
thanks mike, i assumed it was something like that that needs to be done.
__________________
Tranny goes in, tranny comes out, tranny goes in.....AW ****, tranny comes out.... |
#10
|
||||
|
||||
Re: how to adjust the clutch?
You're welcome.
Like anything, adjust in small increments. Its probably different car to car, but a full turn will move my clutch engagement a full inch higher or lower. You do not need to tighten the lock nut to test out where the clutch is. Just turn the rod, get in, put the car into first, slowly release the clutch not using any gas. When you have it where you want, go back and tighten the locking nut.
__________________
Mike 1992 SVX LS-L Pearl White 102,000 miles (Gone) 2005 Evolution 8 SSL Tarmac Black (new daily) 1995 Eclipse GSX Durango Copper Pearl (teh beast) 276awhp/280awtq @ 18psi (560's inj) 260awhp/260awtq @ 17psi (stock inj) |
|
|