Re: Altinator MOD.V4 Supplies?
Quote:
Originally Posted by kjoyes
i plan in replacing postive battery clamp as well'
Here i posted on this before here post too.. http://www.subaru-svx.net/forum/show...ttery+terminal
When the mod is done i will have 3 cables connected to the positive battery terminal?
1st wire being the 4 gauge knukonceptz wire coming from the alternator through the MegaFuse
2nd wire is then the one that get runs from the wiring harness?
3rd wire goes to Fusebox.
|
I would not use the power rings to terminate the wires, but 4 gauge copper battery lugs instead.
The clamp is military-spec and is quite well-made and resists corrosion, Also made of Brass for marine environments
Add one wire to each side as shown or clamp 2 of them on the same side. This gives you a lot of versatility and flexibility to run multiple wires compactly where room is tight, I have used these before without problem/ Just keep all your main harness and fusebox connections on the side of the battery and only the single alternator wire attached to the top.
Available HERE
You can use separate locations to attach cables by using battery side mount screw-in terminals. Same electrical connection.
Quote:
Originally Posted by kjoyes
so my question is the one that comes from the harness goes to the middle of connector of the new battery terminal. I noticed that there is not a lot of wire there to play around with on the harness. then the other 2 wires where the bolts on the new postive post.
can i put power rings on the postive post one from the 4 gauge wire and the other on the one from the fuse box?
|
'.........
__________________
.
Subaru Ambassador
1996 Polo Green LSi #216 ..138,100 miles. ..SOLD
JFICX8659TH100216.....Date of Manufacture: November 16, 1995.....
Fuji Heavy Industries..Ōta North Plant....Ōta City,. Gunma Prefecture, Japan
In-Service Date: January 2, 1997
"The Pristine Green Polo Machine”
First Polo Green on the Network
First Clear front turn signals, JDM Alcyone hood emblem, rear panel, and BOXER engine cover on the Network (US) (2000)
First 5000K HID factory fog lights (2007)
First SVX JDM BBS wheels on a USDM SVX (2013)
HID lighting (5000K) for headlight and H3 fog lights, PIAA SuperExtreme 120W high beams, rebuilt EG33 longblock, Cometic head gaskets, Phase II flexplate, AMR aluminum radiator with custom silicone hoses, 160A high-output alternator in aluminum-ceramic coated case, new design alternator wiring upgrade v.4, rare factory headlight protectors, refinished JDM BBS mesh aluminum wheels and custom, polished billet aluminum new hex center caps, LED grille mod, R1 Concepts high-carbon cryo slotted rotors, Akebono ceramic pads, Goodridge S/S braided brake lines, Smallcar Stage 1 shift kit, ThermalTech aluminum/ceramic-coated valve covers, Energy Suspension urethane front & rear swaybar bushings, Bontrager22 rear swaybar with QS Components Chromoly Teflon/Kevlar endlinks, "$15.00/5 minute" suspension mod. Hella Supertone horns, Custom stainless steel exhaust system with 2" headpipes, Magnaflow cats, AeroTurbine AR25 resonator /AWD "Bullet" muffler.
R.I.P. 2010 Subaru Outback Limited 2.5 CVT...338,000 miles. Totaled by a 1,300 lb. COW March 4, 2016
2014 Hyundai Avante Limited ...178,000 miles. Actually quieter and smoother than the Outback
2007 Mazda Miata MX-5 PRHT...102,000 miles.
Plenty of parts, service and windshields.
4th Registered Network member —2/21/2001
My NEW locker..I...My Email..I..Wikipedia/SVX .
.
|