Forum: General SVX Babble
03-17-2006, 07:13 PM
|
Replies: 18
Views: 4,273
|
Forum: SVX Parts For Sale
01-26-2006, 06:25 AM
|
Replies: 39
Views: 7,400
|
Forum: European Forum
12-23-2005, 10:47 AM
|
Replies: 2
Views: 759
|
Forum: Technical Q & A
07-21-2005, 06:48 AM
|
Replies: 20
Views: 4,015
I do not believe there is a power light on the...
I do not believe there is a power light on the 96's. At least I have not seen one on mine since I bought it almost 2 years ago. There are a few other differences which I can't remember off the top...
|
Forum: Brake Upgrades
07-12-2005, 11:40 AM
|
Replies: 16
Views: 1,893
Brake Clips
The brake line clips I used are Raybestos p/n H1457-2. Hope this helps
|
Forum: Brake Upgrades
07-11-2005, 02:38 PM
|
Replies: 16
Views: 1,893
I just did my brakes this weekend. When you...
I just did my brakes this weekend. When you replace the brake lines make sure you use a good brake line wrench. It looks like a box end wrench with a slot to fit the wrench over the brake line. I...
|
Forum: General SVX Babble
04-21-2005, 10:31 AM
|
Replies: 6
Views: 1,148
|
Forum: Technical Q & A
11-03-2004, 05:19 AM
|
Replies: 12
Views: 1,536
|
Forum: Technical Q & A
10-29-2004, 02:20 PM
|
Replies: 12
Views: 1,536
Follow up - I finally got the car put back...
Follow up - I finally got the car put back together last night and she is running beautifully - knock on wood -. I had to replace the head since the head damage was not repairable. I also had to...
|
Forum: Technical Q & A
10-06-2004, 08:02 PM
|
Replies: 12
Views: 1,536
Well it is possible to get the passenger side...
Well it is possible to get the passenger side valve cover off and remove the cams and lifters. It really wasn't that difficult but I still have to get everything back together.
Unfortunately my...
|
Forum: Technical Q & A
10-06-2004, 07:42 PM
|
Replies: 2
Views: 1,302
Actually they are not obsolete. If you look at...
Actually they are not obsolete. If you look at the website I posted, there is a link with instructions for ordering. Those instructions give you a toll free number to call. I just called them on...
|
Forum: Technical Q & A
10-06-2004, 05:41 AM
|
Replies: 2
Views: 1,302
Subaru Special tools
I found this website while trying to find a Camshaft pulley wrench. I have seen a few posts where people were looking for a special tool and how to get them. This site lists all of the special...
|
Forum: Technical Q & A
09-30-2004, 03:20 PM
|
Replies: 15
Views: 1,575
You will need an OBD II code reader to pull the...
You will need an OBD II code reader to pull the codes and reset. They are not make specific like OBD I so you don't have to find one just for Subarus, but they cost a bit more than OBD I readers. ...
|
Forum: Technical Q & A
09-30-2004, 12:00 PM
|
Replies: 12
Views: 1,536
Commuter:
Bad Lifters: Looking at the...
Commuter:
Bad Lifters: Looking at the service manual it looks like there is a ball check inside, but if none of that is accessible, the only thing I can think of is to make sure the holes are...
|
Forum: Technical Q & A
09-30-2004, 05:48 AM
|
Replies: 12
Views: 1,536
Subaru Diesel?
My 96 developed an awful ticking noise this past weekend that sounds just like a diesel engine (a bad diesel engine at that) at only 55k on the clock. After doing many searches on this forum, I...
|
Forum: Technical Q & A
09-28-2004, 07:48 AM
|
Replies: 10
Views: 995
|
Forum: Technical Q & A
09-28-2004, 05:41 AM
|
Replies: 10
Views: 995
It has been a few months since I did both rear...
It has been a few months since I did both rear wheel bearings with the Hub Tamer. Just to make sure, you are talking about getting the yoke on the hub to press out the old bearing correct?
I had...
|
Forum: Technical Q & A
04-02-2004, 09:31 AM
|
Replies: 1
Views: 1,118
Problem Solved
In case anyone else ever runs into this, I was able to get the outer race out by using part #314302 from the hub tamer kit on the back side of the race and use the hub tamer to press the race out.
|
Forum: Technical Q & A
04-01-2004, 08:24 PM
|
Replies: 1
Views: 1,118
Wheel Bearing: Outer Race stuck
I am currently in the middle of replacing my driver's side rear wheel bearing using the ever popular "hub tamer method". I got the hub out following the hub tamer instructions. The race from the...
|