The Subaru SVX World Network   SVX Network Forums
Live Chat!
SVX or Subaru Links
Old Lockers
Photo Post
How-To Documents
Message Archive
SVX Shop Search
 		IRC users:

Go Back   The Subaru SVX World Network > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search

Showing results 1 to 14 of 14
Search took 1.02 seconds. Search: Posts Made By: VectorNut
Forum: Technical Q & A 07-28-2011, 10:07 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

It's about two inches in diameter. It covered the nut at the front of the inner mount for the front lateral arm. Had a special washer with for tabs to hold it on.
Forum: Technical Q & A 07-28-2011, 09:38 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

Okay, it's finished, the car's back together, I have a feeling I'm running a LOT of negative camber on my left rear wheel, but otherwise it seems to be sound. One question. What's this thing for?
...
Forum: Technical Q & A 07-23-2011, 09:18 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

Okay, I got it out, thank you! Got the stupid bolt out, got the new lateral arm in and the bolt back in. Is there anything special I need to do to pop the axle back in or do I just apply force to the...
Forum: Technical Q & A 07-22-2011, 04:12 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

Okay, just want to make sure I'm using the pry bar in the correct place. Is this where I'm supposed to pry?
...
Forum: Technical Q & A 07-22-2011, 03:11 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

The bolt for the REAR lateral arm has the nut on the front (towards the CV axle) and the bolt comes out the back. It's the bolt for the FRONT lateral arm that won't come out because of the CV boot.
...
Forum: Technical Q & A 07-04-2011, 04:18 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

If you have to cut the old bolt to get it out, you'll have to cut the new bolt to get it in. Which won't work.

The rear bolt attaches differently than the front does, and you can get the bolt out...
Forum: Technical Q & A 07-02-2011, 02:12 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

The bolt at the inner end of the front lateral link won't come out in order for me to remove the inner end of the lateral link from the car. The bolt is a good 3 or 4 inches long, and I can only get...
Forum: Technical Q & A 07-02-2011, 01:00 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

Argh, I'm going to have to remove the CV axle. The bolt holding the lateral link in is 2 inches or so too long to clear the axle. I'm hoping I can just disconnect it from the differential, rather...
Forum: Technical Q & A 07-01-2011, 03:51 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

Am I going to be able to get the bolt out from the inside end of the link without removing the axle?
Forum: Technical Q & A 07-01-2011, 02:39 PM
Replies: 45
Views: 6,985
Posted By VectorNut
Re: Bent rear "toe-in" rod

Hi, guys, so how difficult is it to replace? My left rear suspension has a bent front lateral link from a collision I was in and I got the new part in the mail yesterday. Do I have to disassemble the...
Forum: Technical Q & A 04-14-2009, 01:23 PM
Replies: 35
Views: 4,281
Posted By VectorNut
Re: EGR What is it? How hard to replace.

I've got a '94 that's giving the EGR System code. How likely am I to pass smog with that? I'm also getting a knock sensor and an O2 sensor code, but I have replacement parts for those.
Forum: Technical Q & A 05-24-2007, 10:23 AM
Replies: 9
Views: 1,792
Posted By VectorNut
Thanks, their price was quite a bit higher than...

Thanks, their price was quite a bit higher than Summit Racing -- $89.95 vs. $61.95 -- but they have some other stuff I might be needing to buy from them.



Crap. I should have read your post...
Forum: Technical Q & A 05-22-2007, 10:17 PM
Replies: 9
Views: 1,792
Posted By VectorNut
Do you have the model or part # for your cooler?...

Do you have the model or part # for your cooler? Do I understand correctly that the one you have is the one used in the how-to? I couldn't find any mention of which one is used in the doc.
Forum: Other Mods 05-14-2007, 11:17 PM
Replies: 2
Views: 1,262
Posted By VectorNut
Recommended Upgrades?

I just bought a 94 LS-L that's mechanically stock. I'm very happy with it, but I'd be even more happy if it had more power and a slightly louder, nicer sounding exhaust. While trying to keep the...
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT -6. The time now is 10:24 AM.

Contact Us - SVX World Network - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
© 2001-2015 SVX World Network
(208)-906-1122