The Subaru SVX World Network   SVX Network Forums
Live Chat!
SVX or Subaru Links
Old Lockers
Photo Post
How-To Documents
Message Archive
SVX Shop Search
 		IRC users:

Go Back   The Subaru SVX World Network > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search

Showing results 1 to 13 of 13
Search took 0.05 seconds. Search: Posts Made By: oab_au
Forum: Technical Q & A 11-21-2006, 02:53 PM
Replies: 108
Views: 6,497
Posted By oab_au
The closest to it in a preferred value, would be...

The closest to it in a preferred value, would be two 820 ohm 1/2 watt in parallel, if you can't find 1 watt.

Harvey.;)
Forum: Technical Q & A 11-15-2006, 10:19 PM
Replies: 108
Views: 6,497
Posted By oab_au
The modulated signal from pin c7, does not run...

The modulated signal from pin c7, does not run through the dropping resistor, shift kit circuit, and plays no part in. It is active only when the box is changing gears, or when the ATF is cold.
...
Forum: Technical Q & A 11-15-2006, 08:05 PM
Replies: 108
Views: 6,497
Posted By oab_au
This Quote I pinched from "ItsPeteReally", really...

This Quote I pinched from "ItsPeteReally", really sums up your post, its worthless without numbers.:D


This is the only bit with numbers, so I work on this.



The circuit is shown here.
Forum: Technical Q & A 11-14-2006, 04:25 PM
Replies: 108
Views: 6,497
Posted By oab_au
What a crappy answer,:) I would expect an answer...

What a crappy answer,:) I would expect an answer that has some technical expertize in it, but this is a waste of space.
This is the reasoning that I put forward in suggesting a different value...
Forum: Technical Q & A 11-11-2006, 06:07 PM
Replies: 108
Views: 6,497
Posted By oab_au
Well I have read the whole thread, so may be you...

Well I have read the whole thread, so may be you could point out, where my " values and calculations are wrong"?

Harvey.;)
Forum: Technical Q & A 11-09-2006, 03:24 PM
Replies: 108
Views: 6,497
Posted By oab_au
Don't suppose this was any use.

:p
http://www.subaru-svx.net/forum/showpost.php?p=431697&postcount=40
:cool:

Harvey.;)
Forum: Technical Q & A 10-17-2006, 06:57 PM
Replies: 108
Views: 6,497
Posted By oab_au
I didn't mean to write more on this thread. I was...

I didn't mean to write more on this thread. I was going to write more on the line pressure itself, but this is an expanded version of this post. Is this what you want?

Harvey.;)
Forum: Technical Q & A 10-12-2006, 06:27 PM
Replies: 108
Views: 6,497
Posted By oab_au
Not quite the case Dave. No voltage to the A...

Not quite the case Dave. No voltage to the A solenoid, leaves full line pressure. The A solenoid is a open drain, activating it reduces the line pressure.

Harvey.;)
Forum: Technical Q & A 10-12-2006, 06:23 PM
Replies: 108
Views: 6,497
Posted By oab_au
Yes I have related the current flow that is...

Yes I have related the current flow that is operating in that circuit. The other feed operates independent, of the throttle pressure circuit.

I'll write some on it when I get a chance.
...
Forum: Technical Q & A 10-11-2006, 07:39 PM
Replies: 108
Views: 6,497
Posted By oab_au
I don't think I am confused, in what I have said....

I don't think I am confused, in what I have said. Though I don't understand what you are getting at. Can you explain what you mean by

" on what basis are you claiming that the modulaed secondary...
Forum: Technical Q & A 10-11-2006, 06:10 PM
Replies: 108
Views: 6,497
Posted By oab_au
Power light flashing.

Glad you got that sorted out.:D

As far as the flashing light goes. I think this is caused by the resistor that they have used to increase the dropping resistance. The resistance is too high when...
Forum: Technical Q & A 10-10-2006, 07:31 PM
Replies: 108
Views: 6,497
Posted By oab_au
OK lets look at the three connections that are on...

OK lets look at the three connections that are on the switch. There are three pins on the switch, two have a 670 Ohm resistor soldered across them.
Now when the switch is in the switched condition,...
Forum: Technical Q & A 10-10-2006, 06:11 PM
Replies: 108
Views: 6,497
Posted By oab_au
I am not too sure how the kit ended up being...

I am not too sure how the kit ended up being wired. The theory is to add to the dropping resistors resistance, to reduce the voltage across the A solenoid, to increase the line pressure.

The way...
Showing results 1 to 13 of 13

 
Forum Jump

All times are GMT -6. The time now is 01:09 AM.

Contact Us - SVX World Network - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
© 2001-2015 SVX World Network
(208)-906-1122