Forum: Transmission and Drivetrain
08-19-2015, 11:37 PM
|
|
Replies: 7
Views: 3,111
Re: 8 Speed CVT in SVX
Yes it looks like it would physically fit to me. The transmission control module would be the hurdel to overcome. I do like the CVT though. Will keep looking into this to see what I can come up with.
|
|
Forum: Transmission and Drivetrain
08-16-2015, 10:44 PM
|
|
Replies: 7
Views: 3,111
8 Speed CVT in SVX
Anyone ever tried a CVT install in our cars? I am thinking through some radical mods to my car to make it a much smoother driving car. I have a new outback with CVT and once you get use to it I...
|
|
Forum: General SVX Babble
04-06-2015, 09:44 PM
|
|
Replies: 1
Views: 1,196
Engine Cover
Has anyone tried to put a late model engine cover from an H-6 outback or tribeca on an SVX engine? Looks like they might fit. The outback cover might look cool with polished intake tubes peering...
|
|
Forum: SVX Parts Wanted
07-01-2012, 12:40 AM
|
|
Replies: 3
Views: 1,786
Shifter Arm Washer Needed
Anyone have one of these washers that holds the shifter arm on to the transmission? PM me and we can work out details. Thanks.
|
|
Forum: General SVX Babble
06-28-2012, 10:26 AM
|
|
Replies: 6
Views: 2,114
|
|
Forum: General SVX Babble
06-28-2012, 01:00 AM
|
|
Replies: 6
Views: 2,114
|
|
Forum: General SVX Babble
06-26-2012, 03:51 PM
|
|
Replies: 6
Views: 2,114
Front Strut Top Hat Part Numbers
Looked through the forum a few times. Does anyone know where to get the top hat (strut mount and bearing) for the front struts new? What are the part numbers? Also are their any aftermarket...
|
|
Forum: SVX Parts Wanted
09-25-2010, 09:01 AM
|
|
Replies: 1
Views: 1,234
3.90 Lsd
Having to change transmissions due to it breaking. I have found a 3.90 final drive 5 speed as a replacment but my old one has 4:11. I need a good 3.90 rear LSD to complete the swap. Anyone have one...
|
|
Forum: SVX Parts Wanted
09-15-2010, 09:40 PM
|
|
Replies: 5
Views: 1,387
|
|
Forum: SVX Parts Wanted
09-15-2010, 08:56 PM
|
|
Replies: 5
Views: 1,387
5spd Manual Transmission Needed
Trashed my tranny now need a new one. I have a 97 Legacy 5spd in it now with cable clutch 4:11 gears. Anyone have a very good condition replacement for a decent price please PM me.
|
|
Forum: Technical Q & A
03-27-2010, 12:04 AM
|
|
Replies: 31
Views: 4,221
Re: Noise Under Load and Vibration From Engine
Ahhhh!! The Saga is over for now...
Ok, brand new flywheel from Rock Auto was 8 grams out of balance when balanced with a brand new ACT Stage II pressure plate. Replaced TO bearing, pilot bearing,...
|
|
Forum: Technical Q & A
03-24-2010, 01:01 AM
|
|
Replies: 31
Views: 4,221
Re: Noise Under Load and Vibration From Engine
Update on the noise under load. Pulled the 5MT and tore it down had three bad bearings in the transmission. No wonder it made noise under load. Changing all seals and gaskets while I have it down....
|
|
Forum: Technical Q & A
03-24-2010, 12:55 AM
|
|
Replies: 31
Views: 4,221
Re: Noise Under Load and Vibration From Engine
Iris valve vacuum check valve is located just behind the power steering pump under the intake. It is black and cylindrical shaped and connected to two vacuum lines. I would replace it with a new one...
|
|
Forum: Technical Q & A
03-19-2010, 09:12 AM
|
|
Replies: 31
Views: 4,221
Re: Noise Under Load and Vibration From Engine
Called the Flywheel company and they said the flywheel is zero balanced and therefore does not have any marks on it. You can put the pressure plate in any position and it should be fine.
On...
|
|
Forum: Technical Q & A
03-18-2010, 08:09 PM
|
|
Replies: 31
Views: 4,221
Re: Noise Under Load and Vibration From Engine
I have transmission out and flywheel off. I have a new flywheel but do not see any marks on it. The ACT pressure plate has a mark that looks like an arrow stamped in it. Any ideas on the flywheel?...
|
|
Forum: Technical Q & A
03-18-2010, 07:48 PM
|
|
Replies: 2
Views: 844
|
|
Forum: Technical Q & A
03-18-2010, 06:56 PM
|
|
Replies: 2
Views: 844
90-98 Legacy Manual Transmission Service Manual
Took 93 Legacy transmission apart as it was making a roaring noise. Found some bad bearings. Anyone have a service manual that would have bearing part numbers in it that you could email me? What is...
|
|
Forum: Technical Q & A
02-18-2010, 10:18 PM
|
|
Replies: 3
Views: 994
|
|
Forum: Technical Q & A
02-18-2010, 08:59 AM
|
|
Replies: 3
Views: 994
Exhaust Manifold Studs
Got a couple of exhaust flange studs stripped (2 of the 4 on the exhaust flange where the pipes bolt to the manifolds). Does anyone know the thread and size for these or a part number to buy them?
|
|
Forum: Technical Q & A
02-17-2010, 12:27 AM
|
|
Replies: 31
Views: 4,221
Re: Noise Under Load and Vibration From Engine
So if understand the directions correctly the pressure plate has a "0" mark on it as does the flywheel. The pressure plate must be at least 120 degrees off of the "0" mark in order to be in balance...
|
|
Forum: SVX Parts Wanted
02-15-2010, 10:47 PM
|
|
Replies: 3
Views: 1,430
|
|
Forum: Technical Q & A
02-15-2010, 10:24 PM
|
|
Replies: 31
Views: 4,221
|
|
Forum: Technical Q & A
02-15-2010, 03:09 PM
|
|
Replies: 31
Views: 4,221
|
|
Forum: Technical Q & A
02-15-2010, 02:37 PM
|
|
Replies: 31
Views: 4,221
Re: Noise Under Load and Vibration From Engine
Ok so I pulled the front end off the engine, changed the crank pulley and checked the timing belt to see if it had jumped a tooth. Cams were spot on. Cranked the engine vibration still there at...
|
|
Forum: Technical Q & A
02-14-2010, 11:46 PM
|
|
Replies: 31
Views: 4,221
|
