Sov13t’s Engine and Supercharger Build
Prologue:
This particular project started around May of 2008. Around this time I finished all the minor things I wanted to fix up on the car and it was in great running order, so following logical progression I wanted to set a long term goal both for myself and my car – a challenge, if you may. At first, it was a vague, very general goal: make the SVX perform better. Thanks to numerous conversations with svxfiles (Tom) it started to shape up into a more defined yet very extensive set of objectives. I wanted to run the centrifugal supercharger and push the potential of our engines to new, perhaps even redefining levels. So, the R&D began… Setting goals: My current goals with this project are at 400+ all wheel horsepower. This goal went through multiple revisions, yet it is yet hard to say where we will end up. However, regardless of the numbers a parallel goal for this project is for the car to remain reliable. So we do not want to push 600+, having to start to worry about the transmission, axles, etc… just don’t want to deal with that… ***for now at least*** Summer – Fall 2008: Throughout the summer and fall of this year Tom (svxfiles) and Tom (TomsSVX) helped me with finding proper parts for this type of application. And guess what? When both Tom’s come together and talk engines… it is absolutely overwhelming... That did happen at Pumpkin Carve 2008 – Which marked the ending of the R&D for this project. It was now time to start acquiring all the parts and pieces that were needed. And so, I present you with the components/parts/pieces for this project: Engine: -8.5 C/R Forged, Gas ported CP Pistons Thermal and Friction coated -Eagle Forged H-Beam Rods with ARP 2000 fasteners -ACL Bearings -ARP Head Studs -Cometic Headgaskets copper treated -ECUTune Intake and Exhaust Cams -Custom valve springs -Stainless Steel Intake Valves -Inconel Exhaust Valves -New oil pump, water pump, sensors -New rollers, timing belt -Ceramic coated Intake Manifold with some modifications for better heat exchange Supercharger -Jet Technologies T5 Supercharger - 1700 cfm -Plumbing Electronics and Engine Management -Hydra EMS -MadDad Gauges (Boost, Oil Press., EGT) -Hydra EMS Wide band -740CC Nismo Injectors -GM Open Element IAT Intake and Exhaust -Tomyx -Equal Length Headers -Dual exhaust Transmission -04' USDM 6mt -STi Flywheel -SPEC Stage 3 six-puck clutch and pressure plate Where are we now? The majority of the parts for the engine and ems have been acquired with some exceptions that will be covered within the coming weeks. Also, the transmission and the intake parts have been running on my car for quite some time... however they are just as important for the overall picture... thus needed to be mentioned. I believe slowly but surely this project will be moving into the assembly phase. So up next is the short block then hopefully the long block. Afterward it will be on to the supercharger. Updates will follow as we move along. Budget A lot of $$$ :o When? Who knows? __________________ http://www.sov13t.com/userbar.jpg |
Re: Sov13t’s Engine and Supercharger Build
Awesum project. Post lots of pics :tongue:
|
Re: Sov13t’s Engine and Supercharger Build
Good to hear you've got it all planned out already!
The news from OT about the ARP studs was a great relief! :) Good luck on the project! I shouldn't be to far behind you guys ;):D Dustin |
Re: Sov13t’s Engine and Supercharger Build
Quote:
|
Re: Sov13t’s Engine and Supercharger Build
Quote:
I deffinetly wouldn't have my "project" done by then. Although I will be past the 200awhp mark:D Dustin |
Re: Sov13t’s Engine and Supercharger Build
Some updates...
The short block... http://www.sov13t.com/svx/IMG_3572.jpg The pistons.... http://www.sov13t.com/svx/IMG_3573.jpg http://www.sov13t.com/svx/IMG_3591.jpg http://www.sov13t.com/svx/IMG_3592.jpg http://www.sov13t.com/svx/IMG_3595.jpg http://www.sov13t.com/svx/IMG_3594.jpg More later... |
Re: Sov13t’s Engine and Supercharger Build
Looking good! Where did you get the work done?
|
Re: Sov13t’s Engine and Supercharger Build
We want more! We want more!
|
Re: Sov13t’s Engine and Supercharger Build
Suh-weet!!!
|
Re: Sov13t’s Engine and Supercharger Build
copper gasket paint on the HGs?
-Bill |
Re: Sov13t’s Engine and Supercharger Build
Quote:
that was only "a trick of light and shadow." Teeheeheeheeheehee,snort! |
Re: Sov13t’s Engine and Supercharger Build
Yes copper paint was used on the cometics.
Engine nearing completion ;) Up next... is the fun stuff... :p OT whats that whistling sound? :lol: |
Re: Sov13t’s Engine and Supercharger Build
Quote:
-------------------------------------------------------------------------------- Goose: [describing the supercharged Interceptor that's idling, in particular the supercharger itself] You can shut the gate on this one, Maxie... it's the duck's guts! Barry, MFP Garage Mechanic: [excitedly] She sips nitro... with Phase 4 heads! 600 horsepower through the wheels! She's meanness set to music and the ***** is born to run! Goose: [looking at Max just staring at the engine] He's in a coma, man! |
Re: Sov13t’s Engine and Supercharger Build
More Picsssssssssssssssssssssss
|
Re: Sov13t’s Engine and Supercharger Build
Quote:
When it gets here will post some progress.:) |
All times are GMT -6. The time now is 02:47 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
© 2001-2015 SVX World Network
(208)-906-1122