Wheel Weight Question
 

Hello was wondering if anyone knew how much the stock wheels weigh and the same with the JDM S4 BBS wheels.

Also does anyone know what model of wheel the JDM S4 BBS wheel name or model # is?

Ed
.

Re: Wheel Weight Question
 

.

STOCK OEM 5-spoke wheel (without center cap) weighs 20 lbs. (9.07kg) each.

FORGED JDM BBS wheels (without center cap is) weighs 15.6 lbs (7.08kg.) each. With center cap/waffle ring, the complete wheel weighs exactly 16 lbs. (7.28kg) each.

Just weighed them on my electronic scale a few minutes ago. 20% lighter

http://www.subaru-svx.net/forum/atta...1&d=1517080813

http://www.subaru-svx.net/forum/atta...1&d=1517080813

http://www.subaru-svx.net/forum/atta...1&d=1517080813


JDM S4 BBS wheel is also referred tp as the mesh or cross-spoke design, which superficially resembles a wire wheel and was common on sports cars produced from the 1980s to the early 1990s. This design is light in weight compared to many other styles of the time.

Our wheel is unique and unlike any one that BBS ever made, because of the high positive offset, which gives the outer edge the same profile as the factory rims (for wheel weights) No flat surface or the deep barrel.

One of the most popular BBS produced wheels was the three-piece RS/RG/RZ released in 1977, which became a popular aftermarket wheel and was often replicated by other manufacturers.

Re: Wheel Weight Question
 

.

The edges of the OEM rim and the BBS rims are the same profile


http://www.subaru-svx.net/forum/atta...1&d=1517082992

http://www.subaru-svx.net/forum/atta...1&d=1517082578



As far as other information, maybe the original part number is available from Japanese sources or FHI. I don’t know it offhand and the P/N is now obsolete. Maybe someone knows

These are the only numbers stamped anywhere on the original wheels.


http://www.subaru-svx.net/forum/atta...1&d=1517083186



.

Re: Wheel Weight Question
 

Thanks for the info. I'm thinking of getting a set.

Ed

Re: Wheel Weight Question
 

.
Ed,
Be prepared for people to make fun of you for “skateboard” wheels. Because of how delicate they look they look smaller than the massive 5-spoke OEM, even though they are both 16”

http://www.subaru-svx.net/forum/atta...1&d=1517115147

http://www.subaru-svx.net/forum/atta...1&d=1517115672

Re: Wheel Weight Question
 

Thanks for all the info. I did not end up winning the auction but i will keep an eye out for another set.

ED

Re: Wheel Weight Question
 

.
Then it may look like this.


http://www.subaru-svx.net/forum/atta...1&d=1517195119

.

Re: Wheel Weight Question
 

Which is not a bad thing. I love the look of these wheels.

I also really like the wingless trunk lid. can you just remove it or do you need a special lid?

Re: Wheel Weight Question
 

You can remove the wing but will have to deal with 4 holes. You could put caps in the holes if you can find any that would be waterproof. OR, you could buy a trunk from a wingless car.

Re: Wheel Weight Question
 

.

Like here. Great price and the condition looks very good. Only $139.00

http://elitejdm.com/products/862/

.

Re: Wheel Weight Question
 

But sometimes the journey to get what you want is not cheap nor for the faint of heart.

http://www.subaru-svx.net/forum/showthread.php?t=62770

.

Re: Wheel Weight Question
 

i really like the look of the svx with the JDM wheels, i also have a 96 Polo.

Ed

Re: Wheel Weight Question
 

.
Ed, I specifically posted that photo with you in mind...

.

Re: Wheel Weight Question
 

Thank you for that. Might try and get a S4 chrome grille and wheels and make s4 replica, since i have the corner lights, engine cover, and rear light panel.

Ed

Re: Wheel Weight Question
 

True, but as a Student I cannot justify an expense like that until I graduate. Until then my money goes towards fibreglass, Pore15, and maintenance.

Those are beautiful wheels and they look like they are worth every penny.