The Subaru SVX World Network
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

The Subaru SVX World Network (https://www.subaru-svx.net/forum/index.php)
-   Turbo Projects (https://www.subaru-svx.net/forum/forumdisplay.php?f=35)
-   -   Another Turbo EG33 (https://www.subaru-svx.net/forum/showthread.php?t=59926)

bazza 05-28-2012 01:26 AM
Another Turbo EG33
 
..................

immortal_suby 05-28-2012 05:58 AM
Re: Another Turbo EG33
 
Cool project!

icingdeath88 05-30-2012 12:41 PM
Re: Another Turbo EG33
 
Quote:
Originally Posted by bazza (Post 705221)
WRX turbo oil cooler setup, turbo oil return also pictured:
http://i265.photobucket.com/albums/i...i/IMG_0914.jpg
So how did you plumb the water lines to this thing? There are 2 water lines coming off of it, right? What did you connect them to?

bazza 05-30-2012 07:26 PM
Re: Another Turbo EG33
 
.............................

smc 06-01-2012 11:27 PM
Re: Another Turbo EG33
 
eg33 drysump: http://www.wrxmodders.com/forums/viewtopic.php?p=260946

Dessertrunner 06-02-2012 01:02 AM
Re: Another Turbo EG33
 
bazza in your rebuild what piston, rods & bearings are you going to use?
Tony

bazza 06-03-2012 07:33 AM
Re: Another Turbo EG33
 
.......................

icingdeath88 06-03-2012 12:27 PM
Re: Another Turbo EG33
 
Quote:
Originally Posted by bazza (Post 705639)
Stock pistons, Manley rods and ACL race bearings.

Pistons should hold up fine for 550 hp with E85 - have so thus far with 100+ laps complete.
Stock pistons? That's kind of shocking.

Which ACL bearings are you going to use exactly? I know enough to know that I need two sets of EJ22 bearings but I haven't been able to figure out which brand/type of bearings are best. (Also the EJ22s there are two types of bearings - one with thrust bearing at #3 and one at another, but I don't entirely know what that means or which is right for the EG33.) I have ordered all the parts to build my engine except for those.

bazza 06-03-2012 08:17 PM
Re: Another Turbo EG33
 
......................

icingdeath88 06-03-2012 09:23 PM
Re: Another Turbo EG33
 
Quote:
Originally Posted by bazza (Post 705692)
Shocking in what way, that I'm going to keep using the stock pistons?

Also I bought 2 x sets of EJ2X ACL HX bearings (3# thrust) for my big end. I also have a set of #5 thrust so I'll check everything and report back in detail.
Shocking that you wouldn't go for pistons that are stronger and lower compression. Some people who have broken EG33s with boost have had the pistons go first.

Thanks for the info on the bearings. These, right? http://www.aclperformance.com.au/us/...bearingsus.htm

What do you think for the rod bearings? Same?

92 SVX 06-03-2012 09:45 PM
Re: Another Turbo EG33
 
Quote:
Originally Posted by icingdeath88 (Post 705705)
Shocking that you wouldn't go for pistons that are stronger and lower compression. Some people who have broken EG33s with boost have had the pistons go first.

Thanks for the info on the bearings. These, right? http://www.aclperformance.com.au/us/...bearingsus.htm

What do you think for the rod bearings? Same?
maybe I didnt read it correctly but I think he said he will use the stock 2.2 turbo piston. never mind i reread it he was just comparing stock to 2.2 turbo piston

bazza 06-03-2012 09:52 PM
Re: Another Turbo EG33
 
..........................

Dessertrunner 06-04-2012 01:51 AM
Re: Another Turbo EG33
 
bazza what did the bearing cost you also were did you buy them from?

bazza 06-04-2012 02:34 AM
Re: Another Turbo EG33
 
.............

BackWoodsBob 08-10-2013 05:38 PM
Re: Another Turbo EG33
 
he deleted all his posts?

:unamused:


All times are GMT -6. The time now is 11:46 PM.
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
© 2001-2015 SVX World Network
(208)-906-1122