Metal Radiator
5 Attachment(s)
I have a 92 SVX. Last six in the vin are 105072, it looks to have the stock radiator in it. The radiator is Metal not plastic. When did Subaru start installing the plastic radiators in the SVX ? Does anyone know? And if so why did they put in the plastic radiators?
|
Quote:
To be more factual, the factory radiator is aluminum with plastic top and bottom tanks. The transmission cooler in the lower tank is a single pass and it has been many peoples opinion that the cooler is not efficient enough for the weight of the car and the heat the transmission needs to dissipate. The biggest problems with the plastic tanks is that superheated water from the engine can stress the thermal capabilities of the upper plastic tank when driving "spirited" or doing anything else that causes more heat to be built up (ie A/C in a desert climate, long uphill highway speed grades, etc..) I wiped out TWO radiators in 6 years and thusly started the PWR project. I have since been VERY happy with what PWR has provided us. The biggest obstacle to tackle in the whole ordeal was to get someone to commit to doing R&D to make an after market part for a limited production car that is no longer produced. Again, if you have an all metal/aluminum radiator, can you post pictures?:D |
The radiator in our car is brass,copper, it is not aluminum. I will take a picture tomorrow during daylight and post it. I do not believe anyone has changed the radiator before. It all looks original and has a JB weld patch on the top of it. Thank you for responding so quickly. Fishtail.
|
Speaking of radiators... I am not sure if Subaru ever installed an all metal radiator in SVX other than plastic ones. But my 164s have normal radiator plastic, and all metal engine oil cooler and power steering fluid cooler seperately, I wonder how much heat it develops if these are not htere... :rolleyes: :p
-Pavan |
A car I looked at had the same thing
Looks like it fits alright, but the neck is smaller than the hose I think. At least, the hose looks a little squeezed. http://www.subaru-svx.net/photos/fil...ilot/42914.JPG |
The hose does not fit like it does on the stock ones. :)
|
Looks like something out of a 80's GL or Loyale. I would have to peek in a wrecking yard again.
|
Hate to bug anyone, but theres no How-To document on radiator installation. This will be the first time I've ever done this, any tips? and yes, I have used the search button
|
I will see about making one for you, but rest assured its fairly easy.
Please note, its been several years since I did mine, so this is from memory:
Hope that helps. I will make this better with pictures when the weather clears up a bit an include what size wrenches you will need. Just about everything is like 10mm and 12mm on our car with some of the larger stuff 14mm and 17mm. |
Quote:
|
When removing the fans, one of them is a tight fit. Can't remember which one. I find it easier to remove the transmission cooler lines and then slide the fan down and take it out from underneath the car. ;)
|
well, i have the old radiator out, and I should have the new radiator today. Im a little nervous about how to refill the coolant system. My plan was to reattach all the hoses and fans to the new rad, and just start adding distilled water thru the rad cap while the engine is running and the front of the car is about 8 inches off the ground... is this the right procedure?
|
It's much simpler to remove the radiator with the fans still attached, everything comes out and goes back in smoothly. It also only requires the 4 bolts on top to be removed (instead of the bolts to remove the fans aswell).
Dustin |
no no no, I have the new rad completely in the car, fans and hoses all attached and everything. I filled the radiator with water until it wouldnt take anymore, and the coolant reservior is well above the full mark. There are no bubbles when I run the car up to temperature. Am I all good to go?
I skipped flushing it cuz im lazy and the coolant had been flushed last year. Am I all good |
Run the climate control at full heat and full speed for a few minutes to clear any air in the heater core.
|
All times are GMT -6. The time now is 03:01 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
© 2001-2015 SVX World Network
(208)-906-1122