jman050
10-18-2017, 10:19 PM
https://2.bp.blogspot.com/-PNXyN_pQlVo/Wegh5ynYPVI/AAAAAAAAg3Q/_qa8hiNWMeMzQeKl_1DQ9Dt9Ix4TJcUWwCKgBGAs/s1600/IMG_20171018_075905434.jpg
https://1.bp.blogspot.com/-a6aVdcZvGzc/Wegh51zb07I/AAAAAAAAg3Q/w-CFGcpOoZM1EMUvXmzcG0qV0B3z9_ygwCKgBGAs/s1600/IMG_20171018_052457630.jpg
https://2.bp.blogspot.com/-cduNivpsH9I/Wegh5y9uYUI/AAAAAAAAg3Q/IymsNLi7Wlg8F5Y02bhvmpLe8euxa8o8gCKgBGAs/s1600/IMG_20171017_114555046.jpg
https://4.bp.blogspot.com/--x2lOWJO6xc/Wegh59-DvcI/AAAAAAAAg3Q/0CC6h-4jRjc9mmtKvWhPyXyImRTcUsICQCKgBGAs/s1600/IMG_20171017_132351636.jpg
You need kns adapter Kns-010 $199
Brake caliper hardware from Toyota s12 calipers
Washers for spacing (I had oem Nissan washers from original hardware that was sufficient when added to kns adapter hardware approx $20
Brake lines that fit z32 caliper
Sti rotors 2005+
You have to bring a small corner of material from back of hub on upper mounting hole on svx that I used a Dremel and carbide bit.
Must remove around 1/2 inch on kns adapter around mounting holes that mounts bracket to Svx hub to make it flush I used a 4.5 grinder , metal file and straight edge to ensure I did it evenly.
Toyota caliper hardware lower profile than Nissan although pad design is identical and clearance to inside of wheels on 17" bbs is 1-2mm so that room is critical.
Note: top 8mm or so of pad is left unused and does not contact rotor
https://1.bp.blogspot.com/-a6aVdcZvGzc/Wegh51zb07I/AAAAAAAAg3Q/w-CFGcpOoZM1EMUvXmzcG0qV0B3z9_ygwCKgBGAs/s1600/IMG_20171018_052457630.jpg
https://2.bp.blogspot.com/-cduNivpsH9I/Wegh5y9uYUI/AAAAAAAAg3Q/IymsNLi7Wlg8F5Y02bhvmpLe8euxa8o8gCKgBGAs/s1600/IMG_20171017_114555046.jpg
https://4.bp.blogspot.com/--x2lOWJO6xc/Wegh59-DvcI/AAAAAAAAg3Q/0CC6h-4jRjc9mmtKvWhPyXyImRTcUsICQCKgBGAs/s1600/IMG_20171017_132351636.jpg
You need kns adapter Kns-010 $199
Brake caliper hardware from Toyota s12 calipers
Washers for spacing (I had oem Nissan washers from original hardware that was sufficient when added to kns adapter hardware approx $20
Brake lines that fit z32 caliper
Sti rotors 2005+
You have to bring a small corner of material from back of hub on upper mounting hole on svx that I used a Dremel and carbide bit.
Must remove around 1/2 inch on kns adapter around mounting holes that mounts bracket to Svx hub to make it flush I used a 4.5 grinder , metal file and straight edge to ensure I did it evenly.
Toyota caliper hardware lower profile than Nissan although pad design is identical and clearance to inside of wheels on 17" bbs is 1-2mm so that room is critical.
Note: top 8mm or so of pad is left unused and does not contact rotor